Support road.cc

Like this site? Help us to make it better.

TECH NEWS

Introducing Spoke Fins: swivelling fairings for your spokes

Null Winds Technology device is designed to cut drag in headwinds and crosswinds

US company Null Winds Technology is seeking Kickstarter funding for its swivelling Spoke Fins: nylon plastic fairings that are designed to cut spoke drag in both headwinds and crosswinds.

Fairings for your spokes? Uh-huh!

“Optimally streamlined Spoke Fins reduce the spoke drag coefficient by more than 50% in the critical, faster-moving, drag-inducing region located nearest the wheel rim,” says Null Winds Technology. “Since round spokes have relatively high drag coefficients — thereby becoming the major contributor to overall wheel drag — reducing critical spoke drag also reduces total wheel drag. Spoke Fins are also tapered lengthwise to reduce drag principally on the critical uppermost spokes, where wheel drag most retards vehicle propulsion.

That’s not all.

“As the wheel rotates, Spoke Fins automatically adjust their streamlined alignment for the changing orientation of the effective wind vector impinging on the spoke. Spoke Fins swivel to reduce pedalling effort under any wind condition, becoming especially effective on typical recreational bicycles with higher spoke-counts.”

So, that’s it in a nutshell. There are enough wheels about with bladed spokes; why not just go for a set of those?

“Bicycle racers know that bladed aero-spokes quickly become ineffective in crosswinds,” says Null Winds Technology. “Spoke drag quickly increases when impinging winds are directed crosswise across the flat blades. In a direct headwind, the common round spoke develops more wind drag than does a bladed spoke. However, against a crosswind the bladed spoke can actually produce much more drag than a round spoke.”

Null Winds Technology doesn’t present any wind tunnel data relating to Spoke Fin-equipped wheels. To be fair, that’s understandable because wind tunnel time is very expensive.

The Spoke Fins do, though, seem to fall foul of the UCI’s technical regulations. Article 1.3.011 says, “Any device, added or blended into the structure, that [is] destined to decrease resistance to air penetration or artificially to accelerate propulsion, such as a protective screen, fuselage form of fairing or the like, shall be prohibited.”

Null Winds Technology are seeking US$30,450 (£19,908) to buy the eight-cavity polished steel injection mould it needs to produce Spoke Fins.

Assuming the target is met, a set of Spoke Fins will cost you from US$20 through Kickstarter, although they’ll ship to the US only via this campaign.

For more info go to Kickstarter or www.nullwinds.com

Mat has been in cycling media since 1996, on titles including BikeRadar, Total Bike, Total Mountain Bike, What Mountain Bike and Mountain Biking UK, and he has been editor of 220 Triathlon and Cycling Plus. Mat has been road.cc technical editor for over a decade, testing bikes, fettling the latest kit, and trying out the most up-to-the-minute clothing. He has won his category in Ironman UK 70.3 and finished on the podium in both marathons he has run. Mat is a Cambridge graduate who did a post-grad in magazine journalism, and he is a winner of the Cycling Media Award for Specialist Online Writer. Now over 50, he's riding road and gravel bikes most days for fun and fitness rather than training for competitions.

Add new comment

41 comments

Avatar
Matt eaton | 9 years ago
0 likes

Another whacky kickstarter campaign.

Even if they work we are talking about a product that delivers marginal performance gains and would be illegal for anyone interested in such marginal gains (racers). Seems like another solution looking for a problem.

Avatar
The _Kaner | 9 years ago
0 likes

Can I fit these on my bladed spokes....oh...wait....

Avatar
urbane | 9 years ago
0 likes

 21 This is nonsense without at least some realistic testing e.g. with wind speed regulated fans, strain gauges to measure drag force at the axle mounts and a variable speed wheel drive with power consumption meter to also measure drag force.

I'd also query how quickly the blades can actually move and how long before they break off, and possibly cause a brake fail or wheel stall!

I'll bet that the bladed spokes in my Mavic Crossride wheels are better in most conditions than these toys, including energy savings from better bearings and wheel rigidity; I haven't needed to tweak the spokes at all!

Avatar
djcritchley | 9 years ago
0 likes

Dascinating ... I'll await its adoption by the pro-peleton.

Avatar
eschelar | 9 years ago
0 likes

Last I checked, CFD models don't even bother with spokes because they make basically no difference. They *do* matter when they are large spokes, but as long as there is the same number of spokes (ie 16-24), they are not considered relevant in the aerodynamics.

There's a very good report by a woman who compared CFD for several different mainstream wheels and she gave a very good reason for excluding spokes in her computational models. She also correlated with existing real test data and concluded that they were not relevant. I can't find it, but it's out there for those who like to read extremely long and technical articles.

Now as to adding mass and increasing their size, you are basically taking something that is irrelevant and making it more relevant... probably in a bad way.

The added volume will not decrease turbulence. It *might* increase turbulence, but the Reynolds numbers are just not anywhere near the level where something like this could actually make a difference. Best bet is to just leave your spokes alone.

Avatar
imaca | 9 years ago
0 likes

Forward facing surfaces are far more critical to aerodynamics (hence the effectiveness of "Kammtail", laminar flow wings which have the thickest section nearer the trailing edge, etc) than trailing, so adding a fairing to the back with a circular leading edge (spoke) transitioning messily to the fairing is almost certain to increase drag.

Avatar
Jamminatrix | 9 years ago
0 likes

This looks like a nightmare to keep clean so they spin freely.

Avatar
Vegita8 | 9 years ago
0 likes

I am surprised that people actually thinking about the possibility that this product could improve performance in any shape or form. Did any of you bought the power balance bracelet a couple of years ago?

Avatar
Vegita8 | 9 years ago
0 likes

I am surprised that people actually thinking about the possibility that this product could improve performance in any shape or form. Did any of you bought the power balance bracelet a couple of years ago?

Avatar
armb | 9 years ago
0 likes

Make them retro-reflective, and I might be interested. (Not for racing.)
I'm sure this was tried years ago though, and didn't take off then.

Avatar
Simon Walker | 9 years ago
0 likes

I don't think this will work in the real world. Probably looks like a good idea on a computer screen, all that that extra weight and swivelling will soak up e energy.

Also I bet it rattles like a pissed off snake.

Avatar
Simon Walker | 9 years ago
0 likes

I don't think this will work in the real world. Probably looks like a good idea on a computer screen, all that that extra weight and swivelling will soak up e energy.

Also I bet it rattles like a pissed off snake.

Avatar
Simon Walker | 9 years ago
0 likes

I don't think this will work in the real world. Probably looks like a good idea on a computer screen, all that that extra weight and swivelling will soak up e energy.

Also I bet it rattles like a pissed off snake.

Avatar
Simon Walker | 9 years ago
0 likes

I don't think this will work in the real world. Probably looks like a good idea on a computer screen, all that that extra weight and swivelling will soak up e energy.

Also I bet it rattles like a pissed off snake.

Avatar
Simon Walker | 9 years ago
0 likes

I don't think this will work in the real world. Probably looks like a good idea on a computer screen, all that that extra weight and swivelling will soak up e energy.

Also I bet it rattles like a pissed off snake.

Avatar
Simon Walker | 9 years ago
0 likes

I don't think this will work in the real world. Probably looks like a good idea on a computer screen, all that that extra weight and swivelling will soak up e energy.

Also I bet it rattles like a pissed off snake.

Avatar
ch | 9 years ago
0 likes

Instead of a wind tunnel, they could set up a cheap magnet based speedometer, spin them up to high rpm, and plot graphs of time / speed equivalent as they slow down, both with and without fairings. Yes, it's not the same as a wind tunnel but it would be sufficient to demonstrate principal.
Without even such basic data made available, I am skeptical.  39

Avatar
ch | 9 years ago
0 likes

Instead of a wind tunnel, they could set up a cheap magnet based speedometer, spin them up to high rpm, and plot graphs of time / speed equivalent as they slow down, both with and without fairings. Yes, it's not the same as a wind tunnel but it would be sufficient to demonstrate principal.
Without even such basic data made available, I am skeptical.  39

Avatar
ch | 9 years ago
0 likes

Instead of a wind tunnel, they could set up a cheap magnet based speedometer, spin them up to high rpm, and plot graphs of time / speed equivalent as they slow down, both with and without fairings. Yes, it's not the same as a wind tunnel but it would be sufficient to demonstrate principal.
Without even such basic data made available, I am skeptical.  39

Avatar
CharlesMagne | 9 years ago
0 likes

It's interesting to note that a proper NACA aerofoil has a comparable drag to a circular profile ten times less wide. So I can fully see how it might reduce drag by 50%. And indeed the fairings will orient themselves to the combined vector of spoke through air and cross wind. I suspect they will tend to 'follow' directly behind the spoke as I can't see a cross wind's vector being significantly stronger than that of the spoke through air, particularly at a 'competitive' speed.

Avatar
IrrelevantD replied to CharlesMagne | 9 years ago
0 likes
CharlesMagne wrote:

It's interesting to note that a proper NACA aerofoil has a comparable drag to a circular profile ten times less wide. So I can fully see how it might reduce drag by 50%. And indeed the fairings will orient themselves to the combined vector of spoke through air and cross wind. I suspect they will tend to 'follow' directly behind the spoke as I can't see a cross wind's vector being significantly stronger than that of the spoke through air, particularly at a 'competitive' speed.

As someone pointed out earlier; as the spokes come back down, once they are past horizontal, they are slowing in reference to the airflow vs. forward speed. Now, I'm no physicist, but at some point, they will be effectively in dead air before they start re-accelerating towards the top of their rotational cycle. I imagine in the right conditions, especially at lower speeds, such as steep climbs into strongish winds, you'd get these things flipping back and forth.

If nothing else, I could see that possibly being quite annoying at best, counterproductive at worst. If they can't flip around as fast as the airflow changes from the top to the bottom of the cycle, they'll possibly be creating even more drag.

I'd imagine they might be beneficial for indoors or dead winds, but I don't know that I'd want them when riding into a 20kph+ headwind.

Avatar
Municipal Waste | 9 years ago
0 likes

And these will cause how much fatigue as they move around on the spokes?

Avatar
joemmo replied to Municipal Waste | 9 years ago
0 likes
Municipal Waste wrote:

And these will cause how much fatigue as they move around on the spokes?

Probably bugger all but they might take off the finish on your black spokes.

Avatar
chokofingrz | 9 years ago
0 likes

The centripetal force is what stops flowers from just falling apart. I'm more interested in the centrifrugal force, which is what keeps pulling me back to Lidl for my weekly shop.

Avatar
CygnusX1 replied to chokofingrz | 9 years ago
0 likes
chokofingrz wrote:

The centripetal force is what stops flowers from just falling apart. I'm more interested in the centrifrugal force, which is what keeps pulling me back to Lidl for my weekly shop.

Chapeau!  21  41

Avatar
edster99 | 9 years ago
0 likes

the fairing is interesting in the same way as the spoke fairings. The actual element might be more aero - but the fittings really wont be! Either the slab plates, screws and nuts on fairing, or the ends of each of these 'fairings'. Not convinced without some data to back it up.

Avatar
Mungecrundle | 9 years ago
0 likes

Now I know how some of you rabid disc brake haters feel.

Avatar
jollygoodvelo | 9 years ago
0 likes

Wheel drag retards? Oh.

Avatar
mike the bike | 9 years ago
0 likes

You say tomato, I say tomato. You say centripital, I say centripetal.

Don't worry Darren, whether it's centrifugal force or inertia that throws you across the road, you still end up in the gutter.

Avatar
slam that stem | 9 years ago
0 likes

Centripital force. Centrifugal force doesn't exist. You're not pushed outwards, you're actually pushed inwards. Anyway. ...

All sailors know of somrthing called apparent wind. It's the combined vector of your vehicle's speed and any additional environmental winds.

I agree that the rotation of a spoke (esp over the top) is a much higher velocity than any other vector, except if you live in Holland or Norfolk I suppose

could be useful for a RTW, lejog or RAAM rider?

Maybe this is what Liz Dimmock was waiting for to start her RTW ride?

Pages

Latest Comments