- News
- Reviews
- Bikes
- Accessories
- Accessories - misc
- Computer mounts
- Bags
- Bar ends
- Bike bags & cases
- Bottle cages
- Bottles
- Cameras
- Car racks
- Child seats
- Computers
- Glasses
- GPS units
- Helmets
- Lights - front
- Lights - rear
- Lights - sets
- Locks
- Mirrors
- Mudguards
- Racks
- Pumps & CO2 inflators
- Puncture kits
- Reflectives
- Smart watches
- Stands and racks
- Trailers
- Clothing
- Components
- Bar tape & grips
- Bottom brackets
- Brake & gear cables
- Brake & STI levers
- Brake pads & spares
- Brakes
- Cassettes & freewheels
- Chains
- Chainsets & chainrings
- Derailleurs - front
- Derailleurs - rear
- Forks
- Gear levers & shifters
- Groupsets
- Handlebars & extensions
- Headsets
- Hubs
- Inner tubes
- Pedals
- Quick releases & skewers
- Saddles
- Seatposts
- Stems
- Wheels
- Tyres
- Health, fitness and nutrition
- Tools and workshop
- Miscellaneous
- Cross country mountain bikes
- Tubeless valves
- Buyers Guides
- Features
- Forum
- Recommends
- Podcast
forum
Keo 2 max blade tension blade for Keo 2 blade?
Hi,
I recently upgrade my pedal from Keo 2 Classic to Keo 2 Blade (12Nm).
At the beginning, Keo 2 Blade seems quite good, except it needs a little more force to unclip.
But after sometime, the extra unclip force makes my knee pain, and sometimes makes me unconfident when
I need to unclip in a hurry.
So I'd like to reduce the tension of Keo 2 Blade, but as 12Nm version is already the lowest tension,
it seems impossible to reduce it anymore.
But I found Keo 2 Max blade provides the 8Nm version, and they only have minor difference.
So, is it possible to get an 8Nm Keo 2 max blade tension blade to replace the 12Nm one on Keo 2 Blade?
Thanks.
If you're new please join in and if you have questions pop them below and the forum regulars will answer as best we can.
Latest Forum Topics
Latest Comments
- wtjs 10 min 10 sec ago
Gloucestershire Police said: "Officers are appealing for witnesses after a child cyclist was injured in a collision in Cheltenham last week...
- chrisonabike 15 min 52 sec ago
Worse - people at the Met at least show some emotional response (whether angry denial that they or the officers they know have any issues, misogyny...
- hawkinspeter 18 min ago
I often come into Bristol along the dual carriageway there as it's quicker than trying to find my way on the bike paths, but then I'm used to...
- SecretSam 20 min 54 sec ago
Mini driver. Figures.
- brooksby 1 hour 1 min ago
Looks like local cyclists need to start going along there in primary position then…
- hawkinspeter 2 hours 29 min ago
I re-fuse to believe that not charging drivers is the current attitude
- chrisonabike 3 hours 14 min ago
Well, there are always recumbents!...
- Matthew Acton-Varian 3 hours 24 min ago
Most modern cars, especially SUV's perform very badly on the Moose test. Essentially a stunt driver has to weave through tightly spaced cones at...
- Mr Blackbird 5 hours 41 min ago
His hands are too small to reach the brake levers and his tie gets caught in the chain.
- David9694 15 hours 22 min ago
Further to A Look at Logical Fallacies a couple of months ago. My theory is that 5...
Add new comment
3 comments
Ah. I use the older blade design, which I think needs to be put in while flexed.
Thanks a lot.
Ordered 8Nm replacement kit.
But about the special tool, it seems that only T10 and T8 key is needed to replace it.
https://www.youtube.com/watch?v=VRJI_XAMHjA
So IMHO there is no so-called "special" tool needed to replace it.
It should be, but you'll need to get it done by a retailer for you; it's not a job you can do yourself, I understand.