preferred-google-button
log in
register

Rattling Element Bolt

  • Creator
    Topic
  • December 7, 2018 at 1:55 pm #29187
    bassmanyoowan

    Hi folks,

    I’ve tried googling this issue but haven’t found anything useful so have come here for your collective wisdom.

    I replaced my squashed Garmin 810 with the Element Bolt over a year ago, but after about 6 months the GPS became really loose in mount that it generated an extremely irritating rattle.  I got in touch with Wahoo, and after I sent back my original model I was given a replacement – hurray.

    However, now the new one has developed the same problem.  I really can’t be bothered going through all the faff again with sending it back (their customer service was good so no issues there).  Is there a way I can bodge a repair to stop the rattle?

    Yours in hope,

    Bassmanyooowan

  • Creator
    Topic
Viewing 15 replies - 1 through 15 (of 15 total)
  • Author
    Replies
  • April 17, 2019 at 8:21 pm #932693
    0
    bassmanyoowan

    dave atkinson wrote:

    dave atkinson wrote:

    Sugru. sugru is your friend. work a bit into the mount, put a bit of lube on the computer, push and fix the computer in the mount then remove and let the sugru harden. it’ll take up all the slack and it’s silicone rubber so it’ll dampen any remaining rattles.

    This is way later than it should have been but I tried this and it has worked an absolute treat – thanks Dave!

    December 14, 2018 at 9:04 pm #932691
    0
    Fish_n_Chips
    RDG wrote:
    saves time for catching up on other stuff like the rolling goat f@ck of Brexit/Trump/Environmental Catastrophe/hateful people/Sky etc. Happy Christmas everyone!

     

     lol

    December 12, 2018 at 8:40 am #932689
    0
    RDG

    Hi, a very low tech fix. Cost

    Hi, a very low tech fix. Cost: 0. Time: seconds.

    used it for my rattly Garmin on a SRAM mount.

    take a small half pea sized piece of blue tac, stick it on the mount away from any holes, and voila, no rattle. Just need to roll again each time you remove the unit.

    saves time for catching up on other stuff like the rolling goat f@ck of Brexit/Trump/Environmental Catastrophe/hateful people/Sky etc. Happy Christmas everyone!

    December 12, 2018 at 8:19 am #932687
    0
    StraelGuy
    imajez wrote:
    Been using an Elemnt for several years now and it’s as firm a fit in mount as when I first got it.

     

    Me too but Dave’s idea sounds like an excellent one.

    December 12, 2018 at 1:23 am #932685
    0
    imajez

    Been using an Elemnt for

    Been using an Elemnt for several years now and it’s as firm a fit in mount as when I first got it.

    December 11, 2018 at 8:15 pm #932683
    0
    Fish_n_Chips

    I bought an adapter for my

    I bought an adapter for my Wahoo Bolt that fits to any Garmin.  The adapter hopefully takes up the wear n’ tear.

    Is it a mount problem or the Bolt housing?

    December 11, 2018 at 2:56 pm #932681
    0
    dave atkinson

    Sugru. sugru is your friend.

    Sugru. sugru is your friend. work a bit into the mount, put a bit of lube on the computer, push and fix the computer in the mount then remove and let the sugru harden. it’ll take up all the slack and it’s silicone rubber so it’ll dampen any remaining rattles.

    December 11, 2018 at 2:05 pm #932679
    0
    Rapha Nadal

    I’m sure Wahoo give you the

    I’m sure Wahoo give you the ability to “permanently” fix the unit to the mount by way of a screw.  Have you tried that?  I had a bit of rattle using a K-Edge mount but a bit of inner tube fixed it.  Had the same with my old Garmin.

    December 11, 2018 at 9:30 am #932677
    0
    AfterPeak
    alansmurphy wrote:
    It’s not neccessarily the mounts but the rear housing I’d imagine, once you’ve clicked and turned a couple of hundred times they don’t fit like a glove anymore…

     

    My Garmin mount does and thats after several thousand turns (at least!)

    December 10, 2018 at 3:52 pm #932675
    0
    alansmurphy

    It’s not neccessarily the

    It’s not neccessarily the mounts but the rear housing I’d imagine, once you’ve clicked and turned a couple of hundred times they don’t fit like a glove anymore…

    December 10, 2018 at 1:05 pm #932673
    0
    PRSboy

    If this is a common problem,

    If this is a common problem, might Wahoo have produced a modified mount?… might be worth asking them to send the latest mount on a warranty basis.

     

    December 10, 2018 at 12:50 pm #932671
    0
    alansmurphy

    Oh dear, weren’t we told the

    Oh dear, weren’t we told the Elemnt was the saviour of GPS – now we learn that they won’t stay in a mount for 6 months!

    December 7, 2018 at 9:07 pm #932669
    0
    Paul5f

    This might not be much help

    This might not be much help now but never take it off the mount. I just unscrew the mount from my bars with an Allen key when I need to charge it. Luckily for me a friend got one a few months before me and he very quickly noticed the problems with the mount. 

    December 7, 2018 at 4:23 pm #932667
    0
    Spangly Shiny

    Alternatively you could glue

    Alternatively you could glue in a small piece of an old inner tube. It’s a bit thinner than bar tape but won’t permanently compress.

    December 7, 2018 at 3:41 pm #932665
    0
    bobbydazzler

    I had the same issue with my

    I had the same issue with my Bolt.  The fix I used (and it has worked great for the last year or so) was to cut a small square from some spare bar tape I had and put it in the recessed part of the bracket.  The first few times I put the Bolt on it needed a bit of force, but the tape has compressed now so that you just feel some resistance when twisting it on.  No rattling since!

  • Author
    Replies
Viewing 15 replies - 1 through 15 (of 15 total)
  • You must be logged in to reply to this topic.