log in
register

Replacement Derailleur Hanger

  • Creator
    Topic
  • August 2, 2018 at 1:15 pm #28795
    jonil93

    Hi, 

    I live in Japan but before I moved I arranged to have my Cube Peloton 2014 shipped here from the UK. I had a little crash a few months ago and bent the derailleur hanger, so I ordered a new one. I checked with Cube to make sure I got the right one (number 106 apparently) and I had to order it from Europe because it’s not available here. After paying more for postage than the actual hanger, it finally arrived after a long wait. I tried to fit it yesterday and noticed it’s a different length to the original. It fits in the frame just fine, but I’m wondering if my gears aren’t going to work. 

    I contacted customer service for the place I bought it from and they (understandably) said it’d be fine if I adjust my derailleur setup after. 

    Should I believe them? I have a short cage derailleur with a 12-30T cassette. 

    Thanks in advance 

    Joni

  • Creator
    Topic
Viewing 13 replies - 1 through 13 (of 13 total)
  • Author
    Replies
  • August 7, 2018 at 7:33 pm #924573
    0
    fukawitribe
    srchar wrote:
    Give it a year or two for everyone to upgrade to disc brakes and Road Direct Mount will be the next must-have feature that requires a new frame 🙂

    The Shimano ones all support a hanger adaptor, like how they’re currently fitted to frames not specifically designed around DRD derailleurs.

    August 7, 2018 at 6:59 pm #924571
    0
    srchar

    Give it a year or two for

    Give it a year or two for everyone to upgrade to disc brakes and Road Direct Mount will be the next must-have feature that requires a new frame 🙂

    August 7, 2018 at 10:10 am #924569
    0
    fukawitribe
    srchar wrote:
    Getting even more OT – whatever happened to Shimano’s direct mount derailleur standard, which IIRC removes the need for all this hanger-bending malarkey?

    AFAIK pretty much all newer Shimano RDs are direct mount compatible, MTB ones have been for some while. Plenty of DRD compatible MTB frames as well, not sure how much it’s caught on in the road world.

    August 6, 2018 at 9:58 pm #924567
    0
    srchar

    Getting even more OT –

    Getting even more OT – whatever happened to Shimano’s direct mount derailleur standard, which IIRC removes the need for all this hanger-bending malarkey?

    August 6, 2018 at 9:53 pm #924565
    0
    srchar

     I cut a slot in the end of

     I cut a slot in the end of my homebrew tool and slide a steel rule in it.  Don’t underestimate those basic tools, Doctor.  I think you could knock up a reasonable hanger bender with your drill stand and hacksaw – plus, perhaps, a mitre box, to ensure a square cut in the steel box.  If you use an imperial drill bit (25/64″) rather than a metric one, you won’t have very much play at all – not that it would matter – your tool would trace a cone rather than a disc if you took up the slack.

    A mate of mine has the Park Tool DAG but now borrows my hanger bender; says he doesn’t like the amount of play in the DAG.  I think it cost him well over fifty quid.  Mine cost me a tenner and an hour’s therapy in the shed.

    </parsimony>

     

    August 6, 2018 at 12:47 pm #924563
    0
    Drinfinity
    srchar wrote:
    DaveE128 wrote:
    Wonder if it’s worth buying your own hanger straightening tool for future use?

    A useful addition to the tool box. Alternatively, you can make your own from a length of 20mm steel box, an M10x1 bolt and a couple of washers and nuts.

    Agree it is a useful addition.

    The DIY version sounds like a mech bending tool in my hands. I would need to improvise a sliding gauge to check the alignment relative to the rim, and machine the mounting hole and bolt with a sufficient tolerance that the wobble at the bolt was significantly less than range of satisfactory angles for the mech alignment. Both are outside the tolerances of my diy machine shop, which is basically a drill stand and a hacksaw.

     

    August 6, 2018 at 12:16 pm #924561
    0
    srchar

    DaveE128 wrote:

    DaveE128 wrote:
    Wonder if it’s worth buying your own hanger straightening tool for future use?

    A useful addition to the tool box. Alternatively, you can make your own from a length of 20mm steel box, an M10x1 bolt and a couple of washers and nuts.

    August 4, 2018 at 8:33 am #924559
    0
    Wafty Crank

    Fellow Japan resident here. 

    Fellow Japan resident here.   When I needed a replacement hanger  I ordered a new one from here http://gearmechhanger.com   Sent them a photo of my current hanger and they did the rest.  

    August 4, 2018 at 7:14 am #924557
    0
    DaveE128

    Wonder if it’s worth buying
    Wonder if it’s worth buying your own hanger straightening tool for future use?

    The B-tension adjustment ought to sort it. How big is the difference?

    August 4, 2018 at 12:09 am #924555
    0
    jonil93

    SpikeBike wrote:

    SpikeBike wrote:
    Or take the original to a local bike shop and they will straighten it for you in about 5 seconds

     

    Tried that, I either couldn’t explain it properly or straightening derailleur hangers isn’t a thing here. 

    August 3, 2018 at 8:52 pm #924553
    0
    AfterPeak

    Or take the original to a
    Or take the original to a local bike shop and they will straighten it for you in about 5 seconds

    August 2, 2018 at 7:36 pm #924551
    0
    Canyon48
    srchar wrote:
    Use the B-screw to adjust the jockey wheels closer to the sprockets after fitting the new hanger.

    Agreed, adjusting the B-screw should mean there will be no issues.

    August 2, 2018 at 3:39 pm #924549
    0
    srchar

    Use the B-screw to adjust the

    Use the B-screw to adjust the jockey wheels closer to the sprockets after fitting the new hanger.

  • Author
    Replies
Viewing 13 replies - 1 through 13 (of 13 total)
  • You must be logged in to reply to this topic.