preferred-google-button
log in
register

1x di2 Time trial/triathlon setup

  • Creator
    Topic
  • August 11, 2020 at 9:26 am #31036
    Nicholas dew

    Hello everyone, I was wondering what problems I should look out for if I were to set up a tt bike with: a single 50t chain ring a shimano grx long cage derailleur with an 11-40 cassette.

    Just thinking I could do this with an older tt frame I had and could save some money and weight on shifters and derailleurs.

    Is this crazy or doable. Would I worry about the rear derailleur next to the spokes or would the grx derailleur cope with it?

    Many thanks in advance

  • Creator
    Topic
Viewing 8 replies - 1 through 8 (of 8 total)
  • Author
    Replies
  • August 13, 2020 at 3:53 pm #963395
    0
    njblackadder

    As long as the chain is

    As long as the chain is sufficient for the ‘worst case’, i.e. cassette with largest sprockets, then there would be no problem. You are effectively using sprockets that could be somehwre in the middle of your widest range cassette!

    August 12, 2020 at 3:49 pm #963391
    0
    Nicholas dew

    I would definitely run a
    I would definitely run a narrow wide.

    Thanks

    August 12, 2020 at 3:48 pm #963393
    0
    Nicholas dew

    That’s a good idea I take it
    That’s a good idea I take it a di2 derailleur doesn’t really care what cassette is on the back. Would I need to worry about chain length if I had multiple cassettes.

    August 12, 2020 at 6:22 am #963389
    0
    CXR94Di2

    Ive done this to my Planter X

    Ive done this to my Planter X EXO 2 TT bike.  It had 50/34 crankset 11-25 cassette.  I swapped the double chainring for carbon 58T single and 11-28 cassette. 

    It improves chain line where I mostly have my gearing set on the 13-14t cassette

    I was initially getting dropped chains on bumpy roads, so added a custom made chain guide where the front derailleur was mounted.  There is no real weight advantage, but slimmer bike profile (a little) and positve gear changes.

    Not done any TT this year ,so ;(

     

    August 11, 2020 at 9:00 pm #963387
    0
    BBB

    With a GRX mech (clutch) you
    With a GRX mech (clutch) you could probably get away with any standard chainring but running a narrow wide one would give you almost 100% certainty of not dropping the chain on some choppy tarmac downhill sections. Chainrings with an offset like SRAM X-Sync also improve the chainline. Other than that, there is really nothing else go consider.

    August 11, 2020 at 7:38 pm #963385
    0
    njblackadder

    Hello Nicholas. Fair enough.

    Hello Nicholas. Fair enough. Afraid I can’t help you with the original technical aspects of your question though. Alongside the requirement for the lower gears you wish to use when necessary, I would strongly advise looking into the possibility of having a choice of cassettes for ‘flatter’ courses. In my experience, closer ratios are a good thing for time trials, when feasible. Good luck with it.

    August 11, 2020 at 6:18 pm #963383
    0
    Nicholas dew

    More for covering IM
    More for covering IM triathlon and training 50k plus rides. No way I could get away with 25 and 50 I’d be grinding big time up even a half a mile climb.

    August 11, 2020 at 5:55 pm #963381
    0
    njblackadder

    This is a serious question, I

    This is a serious question, I’m not being facetious. Why on Earth do you want a gear so low on a TT bike? It would need a mountain course to require anything bigger than a 25t sprocket with a 50t ring. If you are planning on riding events where low gears are going to be necessary, my advice would be to get yourself a couple of different cassettes and use the closest ratios you can get away with in each particular race.

  • Author
    Replies
Viewing 8 replies - 1 through 8 (of 8 total)
  • You must be logged in to reply to this topic.