Mounting lights on o/s bars

notfastenough · 2013-03-13T12:26:24+00:00

Hey everyone, I've got some lights from Revolution, but having difficultly mounting the front one. The bars have an oversize centre section (which is covered by the stem clamp), then tapers over the course of maybe two inches where it meets the bar tape. I can't mount it on the taper because it won't sit securely, the bar tape is too thick for it to sit over that, and the clamp cannot be turned 90 degree, so it can't go on the stem. Is it possible to buy an internally-tapered shim that will give the handlebar section a uniform thickness? Any other solution? Cheers.

This topic has 5 replies, 5 voices, and was last updated 13 years, 3 months ago by notfastenough.

Creator

Topic
March 13, 2013 at 12:26 pm #18218

notfastenough

Hey everyone,

I’ve got some lights from Revolution, but having difficultly mounting the front one. The bars have an oversize centre section (which is covered by the stem clamp), then tapers over the course of maybe two inches where it meets the bar tape.

I can’t mount it on the taper because it won’t sit securely, the bar tape is too thick for it to sit over that, and the clamp cannot be turned 90 degree, so it can’t go on the stem.

Is it possible to buy an internally-tapered shim that will give the handlebar section a uniform thickness? Any other solution?

Cheers.
Creator

Topic

Viewing 5 replies - 1 through 5 (of 5 total)

Sort:

Author

Replies
March 14, 2013 at 11:41 am #722243
0

notfastenough

Thanks for the replies,
Thanks for the replies, suppose they’re all a bit of a bodge though really.

@Municipal Waste 😀 They are RSP Compact bars that came with the bike. Googling around, they seem to be usually sold that way, rather than aftermarket. I thought they were 42cm c-to-c, but it turns out that, weirdly, they are quoted as 44cm outside-to-outside, and 41.5cm c-to-c.

I’m looking for a new seatpost anyway (current one has teeth for the tilt adjustment and I can’t get quite the angle I want), so this just means I’ll look for a snazzy matching compact bar and post combo. Any recommendations?

March 13, 2013 at 8:47 pm #722241
0

Municipal Waste

What bars are they?!
What bars are they?!

March 13, 2013 at 8:30 pm #722239
0

cidermart

This any good for
This any good for you?

http://road.cc/content/review/43453-minoura-spacegrip-sgs-300m

March 13, 2013 at 7:58 pm #722237
0

ubercurmudgeon

Buy 26mm diameter handlebars
Buy 26mm diameter handlebars and stem. That will give you a good couple of centimetres on each side of the stem of straight tube for mounting whatever you like. You’ll probably also find it transmits less road vibration and is quite possibly lighter than your current setup. Less stiff, of course, but unless you are either a professional or a gorilla, I doubt it’ll affect your performance and/or enjoyment. Why manufacturers fit oversize bars on anything but out-and-out racing machines I will never understand.

Any form of extended mount will vibrate or fall off. They aren’t designed for lights, only cycle computers

March 13, 2013 at 7:41 pm #722235
0

Gkam84

Stem mount? Similar to
Stem mount? Similar to this

http://www.ebay.co.uk/itm/22g-light-carbon-Computer-mount-Bike-Stem-handlebar-Speedometer-Bracket-Extend-/281009296039?pt=UK_Sporting_Goods_Activity_Monitoring_MJ&hash=item416d7592a7

OR a headset mount like this

http://www.ebay.co.uk/itm/Aest-Handlbar-Stem-Extend-Bracket-Stand-Mount-Speedometer-Computer-Light-Black-/121022032994?pt=UK_Sporting_Goods_Activity_Monitoring_MJ&hash=item1c2d79ac62
Author

Replies

Viewing 5 replies - 1 through 5 (of 5 total)

You must be logged in to reply to this topic.