- News
- Reviews
- Bikes
- Accessories
- Accessories - misc
- Computer mounts
- Bags
- Bar ends
- Bike bags & cases
- Bottle cages
- Bottles
- Cameras
- Car racks
- Child seats
- Computers
- Glasses
- GPS units
- Helmets
- Lights - front
- Lights - rear
- Lights - sets
- Locks
- Mirrors
- Mudguards
- Racks
- Pumps & CO2 inflators
- Puncture kits
- Reflectives
- Smart watches
- Stands and racks
- Trailers
- Clothing
- Components
- Bar tape & grips
- Bottom brackets
- Brake & gear cables
- Brake & STI levers
- Brake pads & spares
- Brakes
- Cassettes & freewheels
- Chains
- Chainsets & chainrings
- Derailleurs - front
- Derailleurs - rear
- Forks
- Gear levers & shifters
- Groupsets
- Handlebars & extensions
- Headsets
- Hubs
- Inner tubes
- Pedals
- Quick releases & skewers
- Saddles
- Seatposts
- Stems
- Wheels
- Tyres
- Health, fitness and nutrition
- Tools and workshop
- Miscellaneous
- Buyers Guides
- Features
- Forum
- Recommends
- Podcast
forum
Novice alert!
I've been commuting to work for a few months now and recently got my hands on a set of bar ends. I went to fit them the other day with the plan to just budge everything on my bars inwards, resulting in enough space to fit the bar ends.....but it turns out the rubber end plugs are attached to a rubber grip that runs underneath my foam grips, making the whole plan a bit more laborious than first expected. I want to get round this problem without resorting to cutting the grips....any one got any decent tips on how to remove the buggers without inadvertently destroying them?
If you're new please join in and if you have questions pop them below and the forum regulars will answer as best we can.
Latest Forum Topics
Latest Comments
- john_smith 2 hours 38 min ago
Straight into the sun is perhaps an exaggeration, but at that time it would be about ESE, and there are bits of the road which head roughly SSE, so...
- john_smith 2 hours 47 min ago
7 October was just a bit of harmless fun until the "msm" ramped it up.
- hawkinspeter 2 hours 47 min ago
It's not censored if you just pirate it
- stonojnr 3 hours 52 min ago
an example of Kesgraves "best cycling infrastructure in the country" https://maps.app.goo.gl/GsCMbzDUTPdq59qS9
- ktache 3 hours 55 min ago
They are not going full gas at every point. They would destroy themselves. And tactics, they save themselves for when effort is really needed....
- wookey 4 hours 24 sec ago
It turns out that that is national police policy. We found out from this process that there is national 'secured by design' policy which causes...
- mtbtomo 4 hours 39 min ago
Been available for quite a while, full GRX mechanical 12 speed. Probably around the same time as 105 mechanical 12 speed if I were to guess.
- TheBillder 4 hours 45 min ago
Less harmful citrus degreaser is easy to find at £8 or less for 5 litres. Works ok for me, even diluted up to 4:1. Both paraffin and white spirit...
- Veganpotter 4 hours 51 min ago
Nope, it's to keep your straps down and quieter. Plus most sunglasses are polycarbonate and aren't going to shatter like glass anyway
- Steve K 5 hours 22 min ago
And, more seriously, where's the coverage of the closure of the cycle lane which forces you to cycle on the Totton bypass.
Add new comment
3 comments
It is difficult to comment without seeing the grips but, when changing the grips on my brompton I was advised to warm the grips with an hair dryer whilst rolling/peeling them off and to my amazement it worked!
Hope this helps
if it's a one-piece rubber sleeve under the foam, it's unlikely you'll be able to do it. Best trick I remember is to actually use a hammer and tap through the grip and use the end of the bar to cut a perfect hole in the end of the grip before you move it inwards to fit the bar ends.
If they're a one piece rubber grip underneath and you want to keep them, I can't see any other way of doing it.
Yes, it is a one-piece rubber sleeve. Someone else mentioned this tip to me I think it might be the one to go with, probably the best method to keep everything looking neat and tidy....the other thing that was suggested was the 'stanley knife option', but that could end up getting a bit messy.