PDW Full Metal Fenders  £60.00


Good quality metal mudguards with the option to fit to race frames.

Contact  www.paligap.cc

by Dave Atkinson   September 30, 2013  

Find a store

These PDW Full Metal Fenders (that's the last time I'll be using that word) look good and perform well, and you can fit them to a bike without eyelets too. Six months in they're still looking good, too.

Full Metal refers to the main part of the mudguard being extruded Aluminium, as opposed to the more usual plastic or plastic-metal construction. Aluminium can corrode, of course, which means it's important that it's treated thoroughly. I've had no issues with any corrosion on my pair, in spite of some rough conditions during testing.

The Full Metals have a single stay (aluminium again) with steel bridge mounts to fit under a calliper brake. Or over, in the case of the rear one: although the mudguard goes under the brake as normal the mount loops over the top. Fitting the 'guards is easy and the stays are telescopic at the end, held in place with a grub screw. I was worried this wouldn't be a very secure way of getting the right length but I've had no issues.

The Full Metals come with pressed steel plates that attach to your quick releases, with a mounting hole for the 'guards, meaning that you can fit them to bikes without eyelets. They're one of only a few 'proper' mudguard sets that offer this as an option. The mounting kit feels a bit cheap compared to the rest of the mudguard but it does the job fine.

You'll need clearance between you brake calliper and your tyre, of course, but for most bikes this won't be a problem. In lieu of a bottom bolt mount at the rear the Full Metals use a mounting block held in place with an O-ring. Again this works fine, and means you don't need a chainstay bridge mounting hole either.

In use these guards are sturdy with the fairly deep profile and long arc catching a good amount of spray. It would be good if longer spray flaps were included, or at least available, but you can easily knock one up if you need it. Despite being primarily metal they're not rattly at all, the only exception being the PDW button on the front mudguard which worked loose. A dab of Araldite sorted that though.

I haven't had to use the emergency quick release function in anger (the mount pops to stop a caught stone catapulting you over the bars) but I've checked it and it works fine, albeit with a bit more force needed than, say, an SKS one.

The Full Metals are designed to be used with a 23mm tyre according to PDW but there's plenty of room for a 25 in there. Even a 28 fits, just.


Good quality metal mudguards with the option to fit to race frames.

road.cc test report

Make and model: PDW Full Metal Fenders

Size tested: n/a

Tell us what the product is for, and who it's aimed at. What do the manufacturers say about it? How does that compare to your own feelings about it?

Made of anodized aluminum and adorned with laser graphics and an embossed alloy head badge, the Full Metal Fenders are a beautiful complement to any road bike. They provide full-wrap coverage, even shielding riders behind you from tire spray thanks to the sturdy rubber mudflaps.

The Full Metal Fenders are designed to fit road bikes that are difficult to install full coverage fenders on. They have special hardware to get around caliper brakes and under forks, even add-on mounts for bikes that lack eyelets to mount fender stays to.

Safety release tabs ensure your wheels will keep turning even if debris gets lodged between the fender and tire.

Rate the product for quality of construction:
Rate the product for performance:
Rate the product for durability:
Rate the product for weight, if applicable:
Rate the product for value:

Tell us what you particularly liked about the product

Look good, sturdy, keep you pretty dry.

Tell us what you particularly disliked about the product

Flaps could be longer, rear mount is unnecessarily fiddly.

Did you enjoy using the product? Yes.

Would you consider buying the product? Yes.

Would you recommend the product to a friend? Yes.

Overall rating: 7/10

About the tester

Age: 40  Height: 190cm  Weight: 102kg

I usually ride: whatever I'm testing...  My best bike is: Genesis Equilibrium with SRAM Apex

I've been riding for: 10-20 years  I ride: Every day  I would class myself as: Experienced

I regularly do the following types of riding: commuting, sportives, general fitness riding, fixed/singlespeed, mtb, Mountain Bike Bog Snorkelling, track


8 user comments

Oldest firstNewest firstBest rated

Ive actually been searching high and low for a set like on this bike http://farm3.static.flickr.com/2118/2335974777_013d932b6b.jpg any suggestions?

posted by jason.timothy.jones [305 posts]
30th September 2013 - 18:55


Considering a pair of these for my winter bike - been looking for a neat set of alloy guards that are lowish profile but offer good coverage, and these seem to fit the bill.

Question - when you mounted them to the Equilibrium, did you mount them to the chainstay bridge, or use their special mount? And is there an alternative to the weird over-brake mounting? I'd probably just use the standard bridge mount behind the brake (I have a spare one knocking around) unless there's a reason it wouldn't fit...

posted by step-hent [716 posts]
1st October 2013 - 9:33


i don't think there's an alternative to the over-the-back-brake mount supplied, no. an SKS one could probably be persuaded to fit.

i used the o-ring mount at the bottom of the rear guard, it works fine

Dave Atkinson's picture

posted by Dave Atkinson [7830 posts]
1st October 2013 - 12:36


Just fitted these today so not been out to test them yet.

They were simple and easy to fit. I think they look as good as full length guards can.

Feel sturdy and they really are low profile.

Bought mine from Tredz - who provided a good service letting me know when they would be in stock etc. (Which they are now.)

willdeath's picture

posted by willdeath [29 posts]
14th October 2013 - 17:46


I have been using these since Feb 13 on my Merida road bike and no issues, they fit well and look good to boot.

posted by cycle zombie [1 posts]
23rd November 2014 - 16:16


I just got some of these for a Spesh Roubaix, they took me several hours to set up, I wasn't rushing though, but I can't even get a 24 mm tyre on the back without rubbing let alone a 25 mm or a 28 mm tyre, I think that is wishful thinking for most bikes because the Roubaix has more clearance than most. The rear rattles like buggery where the guard hits the brake bridge area. I put a tiny foam pad there which should solve that issue but of course it made the rubbing even worse. I have now put a 23 mm on the back and that seems ok but I haven't been out on it yet. I was using cruds before and they give more coverage on the seat tube and bottom bracket area so they keep the bike cleaner and they are much lighter and cheaper but not as neat.These do look good and they are sturdy so without rattle and rub (hopefully) I should be happy with them. The front one doesn't seem to rattle and works well with a 23 mm tyre, I tried it with a 24 but there is very slight rub.
Another thing to watch for is the stay bolts came loose on one of my rides and I had to come home because they take a tiny allen key that you don't normally find on multi-tools, so they need checking and doing up tight but I carry the tool now. Also, you have to remove the QR fully to get the wheels off, obviously, and spare hardware is available for about 15 quid if you lose anything. These guards are an expensive option but posiibly worth it, at least with 23 mm tyres.

posted by Anthony.C [85 posts]
2nd December 2014 - 11:00


Anybody know who the importer is for these? I am after the over brake mount not the full guards whech they sell as a separate kit.

Currently using lightly modified SKS guards with the normal style mounting bracket on my CAAD8. I just need an extra fag papers width of clearance on the back wheel to run a 28 mm with no rub which this mount bracket might provide.

posted by P3t3 [163 posts]
2nd December 2014 - 11:24


You can get the mount in the PDW full metal fenders hardware pack, vanillabikes seem to be the cheapest.

posted by Anthony.C [85 posts]
2nd December 2014 - 11:35