- News
- Reviews
- Bikes
- Accessories
- Accessories - misc
- Computer mounts
- Bags
- Bar ends
- Bike bags & cases
- Bottle cages
- Bottles
- Cameras
- Car racks
- Child seats
- Computers
- Glasses
- GPS units
- Helmets
- Lights - front
- Lights - rear
- Lights - sets
- Locks
- Mirrors
- Mudguards
- Racks
- Pumps & CO2 inflators
- Puncture kits
- Reflectives
- Smart watches
- Stands and racks
- Trailers
- Clothing
- Components
- Bar tape & grips
- Bottom brackets
- Brake & gear cables
- Brake & STI levers
- Brake pads & spares
- Brakes
- Cassettes & freewheels
- Chains
- Chainsets & chainrings
- Derailleurs - front
- Derailleurs - rear
- Forks
- Gear levers & shifters
- Groupsets
- Handlebars & extensions
- Headsets
- Hubs
- Inner tubes
- Pedals
- Quick releases & skewers
- Saddles
- Seatposts
- Stems
- Wheels
- Tyres
- Health, fitness and nutrition
- Tools and workshop
- Miscellaneous
- Buyers Guides
- Features
- Forum
- Recommends
- Podcast
TECH NEWS
trek project one video 01Video: Inside Trek's Project One
This video takes you on a tour of Trek’s Waterloo, Wisconsin factory, where they still make many of their top-end bikes like the Madone 6 and 7, and includes their custom paint and bike builder facility Project One.
Trek Bicycles, founded in 1976, actually started making their first carbon fibre bicycles frames with the introduction of the 5500 and 5200 road bikes in 1992. They used Trek’s proprietary OCLV (Optimum Compaction, Low Void) manufacturing process, which they still use to this day. While many of the cheaper carbon bikes are now made in Taiwan, they still make their top of the range models in the US.
And if you order a bike through Trek's Project One website, this is where they are assembled. The custom bike builder lets you choose from a raft of paint options as well as specifying the wheels, groupset and components.
David worked on the road.cc tech team from 2012-2020. Previously he was editor of Bikemagic.com and before that staff writer at RCUK. He's a seasoned cyclist of all disciplines, from road to mountain biking, touring to cyclo-cross, he only wishes he had time to ride them all. He's mildly competitive, though he'll never admit it, and is a frequent road racer but is too lazy to do really well. He currently resides in the Cotswolds, and you can now find him over on his own YouTube channel David Arthur - Just Ride Bikes.
Latest Comments
- Hirsute 2 hours 41 min ago
Radar tells me their closing speed, if they are slowing and how far away. Then I decide to say a prayer. The change of light pattern is incidental.
- lonpfrb 3 hours 1 min ago
Quite so, which is why our village 20mph zone covers the whole residential extent. Of course, enforcement is another thing..
- lonpfrb 3 hours 27 min ago
No, that's very doubtful while proper testing would be fully destructive.
- TheBillder 4 hours 13 min ago
In that £1000 exactly scenario, beginners should probably be made aware that pedals will be extra.
- don simon fbpe 4 hours 41 min ago
What's wrong with dropping down on to the Millenium Bridge, or the swing bridge, then the brief, but satisfying climb back up the hill? #training....
- chrisonabike 5 hours 22 min ago
The relatives might of course disagree, but in general I'd countenance a relatively light sentence* if only we could fix it so that those who...
- ktache 6 hours 1 min ago
Id forgotten that I got a second hand set of project two's for my getting to work bike over twenty years back.
- Veganpotter 6 hours 58 min ago
My bet is that all these tires popping off are from people with bad pressure gauges or they're simply just putting too much air in on purpose. ...
- chrisonabike 8 hours 14 min ago
David9694 - you were right! These new autonomous vehicles really are conspiring to run out of control!...
Add new comment
4 comments
Did wonder how much detail they'd go into on the moulding and curing process. not too surprised to see that it was "almost no detail at all".
Geez a job ...
I do quite fancy one of these, a madone in either Jens or Spartacus colours ideally, however I cant get over the fact that when im spending that much money I would want different finishing kit and probably custom geometry.
Ahem...1976.