- News
- Reviews
- Bikes
- Accessories
- Accessories - misc
- Computer mounts
- Bags
- Bar ends
- Bike bags & cases
- Bottle cages
- Bottles
- Cameras
- Car racks
- Child seats
- Computers
- Glasses
- GPS units
- Helmets
- Lights - front
- Lights - rear
- Lights - sets
- Locks
- Mirrors
- Mudguards
- Racks
- Pumps & CO2 inflators
- Puncture kits
- Reflectives
- Smart watches
- Stands and racks
- Trailers
- Clothing
- Components
- Bar tape & grips
- Bottom brackets
- Brake & gear cables
- Brake & STI levers
- Brake pads & spares
- Brakes
- Cassettes & freewheels
- Chains
- Chainsets & chainrings
- Derailleurs - front
- Derailleurs - rear
- Forks
- Gear levers & shifters
- Groupsets
- Handlebars & extensions
- Headsets
- Hubs
- Inner tubes
- Pedals
- Quick releases & skewers
- Saddles
- Seatposts
- Stems
- Wheels
- Tyres
- Health, fitness and nutrition
- Tools and workshop
- Miscellaneous
- Buyers Guides
- Features
- Forum
- Recommends
- Podcast
forum
HELP please
Hi, I hope someone may be able to help.
I have a Focus Cayo with PF30 BB. I've removed the old and replaced with a WMF BB and all went well using Park Tools press.
I have SRAM Red 22 crankset and replaced the non drive side through the BB, when attaching the drive side all is good, spinning freely, until I tighten up the 10mm bolt. I haven't got anywhere near the recommended torque but it stops spinning completely!
I have replaced gutter seals and recommended spacers that came with New BB and am totally lost... Have the etape next weekend and wondered if anyone could offer advice?
Thanks very much in advance.
If you're new please join in and if you have questions pop them below and the forum regulars will answer as best we can.
Latest Forum Topics
Latest Comments
- john_smith 2 hours 38 min ago
Straight into the sun is perhaps an exaggeration, but at that time it would be about ESE, and there are bits of the road which head roughly SSE, so...
- john_smith 2 hours 47 min ago
7 October was just a bit of harmless fun until the "msm" ramped it up.
- hawkinspeter 2 hours 47 min ago
It's not censored if you just pirate it
- stonojnr 3 hours 52 min ago
an example of Kesgraves "best cycling infrastructure in the country" https://maps.app.goo.gl/GsCMbzDUTPdq59qS9
- ktache 3 hours 55 min ago
They are not going full gas at every point. They would destroy themselves. And tactics, they save themselves for when effort is really needed....
- wookey 4 hours 24 sec ago
It turns out that that is national police policy. We found out from this process that there is national 'secured by design' policy which causes...
- mtbtomo 4 hours 39 min ago
Been available for quite a while, full GRX mechanical 12 speed. Probably around the same time as 105 mechanical 12 speed if I were to guess.
- TheBillder 4 hours 45 min ago
Less harmful citrus degreaser is easy to find at £8 or less for 5 litres. Works ok for me, even diluted up to 4:1. Both paraffin and white spirit...
- Veganpotter 4 hours 51 min ago
Nope, it's to keep your straps down and quieter. Plus most sunglasses are polycarbonate and aren't going to shatter like glass anyway
- Steve K 5 hours 22 min ago
And, more seriously, where's the coverage of the closure of the cycle lane which forces you to cycle on the Totton bypass.
Add new comment
3 comments
Lol, thanks for the genuine help and for the not so helpful!
Plastic spacers were at fault! Just took this spanner monkey too long to figure out
Are you sure the bearings are fully inserted into their housings?
With the crank removed do the bearings spin freely by hand?
It sounds to me like one of the bearings is not fully in which is off setting the crank, so when it comes to putting the arm on it is too close to the frame.
Take it to a bike shop, admit to being a cack handed spanner monkey, and get it fixed.